Welcome to the MacNN Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

You are here: MacNN Forums > Hardware - Troubleshooting and Discussion > Mac Desktops > PMG5 (Dual Proc 2.5) Power Issue

PMG5 (Dual Proc 2.5) Power Issue
Thread Tools
Junior Member
Join Date: Sep 2009
Status: Offline
Reply With Quote
Oct 6, 2009, 02:01 AM
 
Hey guys, my 2.5DP (June 2004) has started having an issue where it will randomly power off without warning or provocation. It even went a few months without powering on at all. Strangely, wiggling the RAM revived it from that coma but a few days later it did it again. Do you think it is the 600W power supply, or something else?

--kevin
     
Administrator
Join Date: Jun 2000
Location: California
Status: Online
Reply With Quote
Oct 6, 2009, 03:14 AM
 
Look over your motherboard, paying attention to the capacitors. Note if any show bulging on top (the tops should be perfectly flat) or brown leakage. ref Capacitor Plague

If it were bad capacitors, the power supply is a more likely place to look. But it's rather hard to inspect in a PowerMac G5.
     
Grizzled Veteran
Join Date: Oct 2008
Location: UKland
Status: Offline
Reply With Quote
Oct 6, 2009, 12:34 PM
 
Sigh. The power supply on these is also shockingly prone to early death. It's a pain to get out as you need to dismantle the Mac, removing the processors (among other things). It's unlikely to be bad capacitors as that seems to be one problem that G5's didn't suffer from so much. There was an Apple recall programme for PSU's but it's over now.

It's quite easy to grow to hate G5 powermacs.
     
Administrator
Join Date: Jun 2000
Location: California
Status: Online
Reply With Quote
Oct 6, 2009, 01:13 PM
 
The repair extension is over for G5 iMacs. An extension remains in effect for some PowerMac G5 models.
     
Junior Member
Join Date: Sep 2009
Status: Offline
Reply With Quote
Oct 6, 2009, 11:16 PM
 
yes, as i've mentioned in other threads. regardless, the REP for the power mac PSU is only referring to the 700w and 1000w models, not the 600w in the dual 2.5. i'm screwed either way. i've tried to get apple to CS code it a few times with no luck. at least the processors are easy to pull, i built my first g5 from a pile of parts so i'm pretty familiar with them. ironically, that one (which i sold) works way better to this day than either of my 2 current G5s! it is possible to get the PSU out without removing the board, that saves a lot of time. not as bad as it could be it just sucks how much those things cost. but, that's the beauty of apple, i could sell this 4 year old machine (working) for about as much as i spent building my core 2 quad w/ 1gb gts 250 future hackintosh!
     
Junior Member
Join Date: Sep 2009
Status: Offline
Reply With Quote
Oct 16, 2009, 06:48 AM
 
ok so regardless of the REP, has anyone else had this issue? i wish i had more parts to test with. i've left it off and unplugged for a few days, so when i go plug it in and fire it up in a moment it should probably work fine, at least for a while.
     
   
Thread Tools
Forum Links
Forum Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On
Top
Privacy Policy
All times are GMT -5. The time now is 12:31 PM.
All contents of these forums © 1995-2011 MacNN. All rights reserved.
Branding + Design: www.gesamtbild.com
vBulletin v.3.8.7 © 2000-2011, Jelsoft Enterprises Ltd., Content Relevant URLs by vBSEO 3.3.2