|
|
Gigabit G4 Network
|
|
|
|
Mac Enthusiast
Join Date: Jan 2003
Location: :noitacoL
Status:
Offline
|
|
I have the above... (400mhz model) and the ethernet doesn't seem to work... However it shows up in apple system profiler, it shows this when I type ifconfig en0 into terminal:
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULT ICAST> mtu 1500
ether 00:30:65:7c:28:3a
media: autoselect (none) status: inactive
supported media: none autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,hw-loopback> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,hw-loopback> 1000baseT <full-duplex> 1000baseT <full-duplex,hw-loopback> 1000baseT <full-duplex,flow-control> 1000baseT <full-duplex,flow-control,hw-loopback>
But, when I plug a cable into it, I get nothing on the router... I know the cable and router are fine as I plugged the same cord on the same port into my iMac and it was surfing fine... I tried to install a third party card... It gets the lights and all, shows up on the router, but doesn't show up in the network CP. Luckily I have a third party airport card in there that works fine... I tried swapping PCI slots and resetting the motherboard and even pulling out the pram battery for about 10 mins.
So, is my onboard dead? And if it is, why does it show up in ASP and the Network CP and ifconfig en0? Am I just boned for hardwired networking now?
Thanks in advance.
|
All as artificial as the Matrix itself, although only a human mind could invent something as insipid as Love.
|
|
|
|
|
|
|
|
Junior Member
Join Date: Jul 2003
Status:
Offline
|
|
So, are you saying your Mac doesn't connect to your router via DHCP? Is that how it's set up?
Does it show up with a junk IP?
How are you determining it is not connecting? Can you connect to your router's web configuration page? (Usually 192.168.1.1)
What other devices do you have on the network that you can test/ping/etc.?
We need more specifics!
regards,
MAJ
|
|
|
|
|
|
|
|
|
Mac Enthusiast
Join Date: Jan 2003
Location: :noitacoL
Status:
Offline
|
|
no... no ip or anything fills in IN network CP when I select it... If I take out that cord and plug it into the side of my iMac, it immediately gets an IP and can go...
I've looked inside and nothing seems loose... don't know why it wont work... or recognize the card...yeesh...
|
All as artificial as the Matrix itself, although only a human mind could invent something as insipid as Love.
|
|
|
|
|
|
|
|
Mac Enthusiast
Join Date: Jan 2003
Location: :noitacoL
Status:
Offline
|
|
|
All as artificial as the Matrix itself, although only a human mind could invent something as insipid as Love.
|
|
|
|
|
|
|
|
Junior Member
Join Date: Jul 2003
Status:
Offline
|
|
Try selecting the options in the Network CP manually and force it to a different configuration.
Show "Built-in Ethernet"
Select "Ethernet" tab
Configure "Manually (Advanced)"
Then try:
Speed "100baseTX" or "10baseT/UTP"
Just as an example.
Change Duplex, if nothing goes.
My G5 at work wouldn't connect to our Gigabit switch until I manually switched it to 100base.
regards,
MAJ
BTW, what kind of router is this?
|
|
|
|
|
|
|
|
|
Mac Enthusiast
Join Date: Jan 2003
Location: :noitacoL
Status:
Offline
|
|
It's a wireless belkin off the cable modem... got a long cable connecting it to an AsantĂȘ router that I have configured as a hub... runs my iMac fine... of any unused port...
|
All as artificial as the Matrix itself, although only a human mind could invent something as insipid as Love.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Forum Rules
|
|
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
|
HTML code is Off
|
|
|
|
|
|
|
|
|
|
|
|