Welcome to the MacNN Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

You are here: MacNN Forums > Hardware - Troubleshooting and Discussion > Mac Desktops > The 1.33 Ghz emac is here

The 1.33 Ghz emac is here
Thread Tools
Anand
Mac Enthusiast
Join Date: Oct 2000
Location: Between heaven and hell
Status: Offline
Reply With Quote
Jan 5, 2004, 05:01 PM
 
http://www.lbodnar.dsl.pipex.com/eMac/eMac-upgrade.html

Anyone else willing to give it a try?
Yes, I know I could buy a PC, but why?
     
bradoesch
Professional Poster
Join Date: Jun 2000
Status: Offline
Reply With Quote
Jan 5, 2004, 05:14 PM
 
Overclocking my iMac DV is similar, but I'd never have the guts to try. I run my Pentium 3 450 MHz at 600 Mhz no problem (by changing the bus speed from 100MHz to 133 MHz), because I don't care about that machine. I'm either too scared or too wise to keep the soldering iron away from my iMac.
( Last edited by bradoesch; Jan 18, 2004 at 12:32 AM. )
     
nredman
Addicted to MacNN
Join Date: Jul 2002
Location: Minnesota - Twins Territory
Status: Offline
Reply With Quote
Jan 5, 2004, 05:43 PM
 
1ghz is fine for me...but if i ever want to get kicked in the nuts i'll try it.

"I'm for anything that gets you through the night, be it prayer, tranquilizers, or a bottle of Jack Daniel's."
     
Eriamjh
Addicted to MacNN
Join Date: Oct 2001
Location: BFE
Status: Offline
Reply With Quote
Jan 5, 2004, 06:19 PM
 
Hmmm. An 800MHz eMac running at 1.33GHz with no mods (except jumpering).

Sounds fishy.

I'm a bird. I am the 1% (of pets).
     
Lateralus
Moderator Emeritus
Join Date: Sep 2001
Location: Arizona
Status: Offline
Reply With Quote
Jan 6, 2004, 01:45 AM
 
Originally posted by Eriamjh:
Hmmm. An 800MHz eMac running at 1.33GHz with no mods (except jumpering).

Sounds fishy.
A little fishy, but not beyond the realm of possability. Consider the fact that the eMac is based around the 7455 G4 chip, which ranges in clock speed from around 800MHz all the way up into the 1.4GHz range. So, it is entirely possible I would imagine, to overclock a 7455 to speeds that high. Because chances are that the 7455s were actually underclocked by Apple as a means of product protection, to keep the iMac and eMac from competing with the Power Mac line by way of clock speed.
I like chicken
I like liver
Meow Mix, Meow Mix
Please de-liv-er
     
Will C
Mac Enthusiast
Join Date: Jan 2001
Location: London, UK
Status: Offline
Reply With Quote
Jan 6, 2004, 08:06 AM
 
I think it looks good - I've emailed the user to ask further questions - like 'if you live nearby can I come and see it?'
     
the_glassman
Mac Elite
Join Date: Apr 2003
Location: Anywhere but here.
Status: Offline
Reply With Quote
Jan 10, 2004, 05:11 PM
 
Any updates?
I think it would be awesome, I would love to OC my 1 GHz to something like 1.3 or 1.5.
     
cdhostage
Mac Elite
Join Date: Jul 2001
Status: Offline
Reply With Quote
Jan 11, 2004, 12:58 AM
 
Overclocking an eMac. Ah, I suppose it'd be fine. I bet that increasing the core voltage slightly would allow that 1.4 GHz jump. I'd put a big, quiet fan immediately below the grille on the back and call it a day.

That display trick is a little iffy.
Actual conversation between UCLA and Stanford during a login on early Internet - U: I'm going to type an L! Did you get an L? S: I got one-one-four. L! U:Did you get the O? S: One-one-seven. U: <types G> S: The computer just crashed.
     
lbodnar
Fresh-Faced Recruit
Join Date: Jan 2004
Location: UK
Status: Offline
Reply With Quote
Jan 11, 2004, 07:26 AM
 
Hello guys, I am the owner of the updated eMac.

Mike from www.xlr8yourmac.com does not believe it either.
I am on a broadband so if you want to telnet or SSH or even get remote desktop on it for testing you are welcome. Just let me know.

1.33->1.4 is not worth messing around with voltages. It is so sweet to do nothing but move a jumper and have 60% speed increase! I believe they use underclocked CPUs because Motorola does not make 800MHz chips anymore.
     
Grrr
Grizzled Veteran
Join Date: Jun 2001
Location: London'ish
Status: Offline
Reply With Quote
Jan 11, 2004, 09:58 AM
 
Originally posted by cdhostage:
That display trick is a little iffy.
Not at all.. It's a relatively straight forward software hack that I have done on my eMac too. The graphics chips are perfectly capable of running 2 screens. But Apple blocks this function on all ATI eMacs, iMacs and iBooks, so as to at least partly justify the cost of their more expensive machines. Did it to my eMac on the very day I got it. Zero problems to date. The hack simply lifts Apples block.. Thats all.

The over clocking mod looks interesting too. Perhaps one day i'll give that a shot also.. Nice work
The worst thing about having a failing memory is..... no, it's gone.
     
acX
Fresh-Faced Recruit
Join Date: Jun 2002
Location: Maryland
Status: Offline
Reply With Quote
Jan 11, 2004, 06:19 PM
 
Originally posted by Anand:
http://www.lbodnar.dsl.pipex.com/eMac/eMac-upgrade.html

Anyone else willing to give it a try?
OK, I could not stand it anymore..
I took my 800Mhz eMac which I had bought as a $529 Apple refurb. I already put more RAM, a DVD-106 superdrive, and a 120 GB 7200 RPM drive in it.

I decided to do as little as possible, so I soldered the jumper in between the bottom two to yield 1.066 Ghz.
The system has been up and running for hours now without a hitch. The speed is reported as 1.07 Ghz. My initial xbench score is a little over 110. I have 640 MB of ram.

So far so good. It was not too easy doing that solder job, I think I will leave it alone for a while now.. If I ever decide to do more, I'm taking it to work where we have a lab to work on things like this..

ac
     
Grrr
Grizzled Veteran
Join Date: Jun 2001
Location: London'ish
Status: Offline
Reply With Quote
Jan 11, 2004, 09:38 PM
 
Originally posted by acX:
OK, I could not stand it anymore..
Hehe, I'm feeling that way too now. And now i am seriously thinking about dusting off my soldering iron.. Looks like it would be relatively straight forward to take my 1ghz eMac up to 1.2ghz, as all I have to do is remove 3 SMD jumpers. Thats it. No need to replace any to new locations at all.
Who would it have thought it eh.. Remove 3 tiny components for a 20% speed boost
The worst thing about having a failing memory is..... no, it's gone.
     
chabig
Addicted to MacNN
Join Date: Jun 1999
Location: Las Vegas, NV, USA
Status: Offline
Reply With Quote
Jan 11, 2004, 09:54 PM
 
Just removing 2 jumpers will take your 1GHz to 1.266GHz.
     
the_glassman
Mac Elite
Join Date: Apr 2003
Location: Anywhere but here.
Status: Offline
Reply With Quote
Jan 13, 2004, 06:57 PM
 
Originally posted by chabig:
Just removing 2 jumpers will take your 1GHz to 1.266GHz.
Ah, but which ones?
I'm also intrigued of this idea with the new 800 MHz ibooks, I wonder how hard it would be to overclock them?
I could get a base ibook with cd-rom drive from the education store for $949, and rip it apart, upgrade the drive to a superdrive, over clock it and add a larger hard drive.
     
Grrr
Grizzled Veteran
Join Date: Jun 2001
Location: London'ish
Status: Offline
Reply With Quote
Jan 13, 2004, 08:09 PM
 
Originally posted by the_glassman:
Ah, but which ones?
The ones that are displayed on that site who's URL was shown in the 1st post here
For someone with decent soldering skills, it should not be too hard to do at all.. When time allows, i'll give it a go for sure.
The worst thing about having a failing memory is..... no, it's gone.
     
CobaltGT
Junior Member
Join Date: Dec 2001
Location: Georgia Tech
Status: Offline
Reply With Quote
Jan 16, 2004, 07:05 PM
 
my 1ghz is running at 1.4 thanks to that article. it passed the stress test. is the fan temp controlled? i overclocked it without ever turning it on and it makes a ton of noise, but maybe it's the excess heat...
     
lbodnar
Fresh-Faced Recruit
Join Date: Jan 2004
Location: UK
Status: Offline
Reply With Quote
Jan 16, 2004, 07:15 PM
 
Originally posted by CobaltGT:
..is the fan temp controlled? i overclocked it without ever turning it on and it makes a ton of noise, but maybe it's the excess heat...
CobaltGT, it seems that the fan does not change the speed at all. Compare its speed right after turning eMac on and after few hours under 100% load - it is the same (=loud).
     
rcitrin
Fresh-Faced Recruit
Join Date: Aug 2003
Location: Boston, MA
Status: Offline
Reply With Quote
Jan 16, 2004, 08:22 PM
 
Could someone further explain to me the soldering part...

I have never soldered before, and while it does not seem terribly complex, in his diagram (from how I read it) he shows soldering 2 jumpers together that are not next to each other to get from 800mhz to 1.3 ghz.

I would really appreciate any help, as I am seriously considering doing it...I mean I only paid $500 for it...

Thanks guys!!

R.
     
klinux
Senior User
Join Date: Jul 2002
Location: LA
Status: Offline
Reply With Quote
Jan 16, 2004, 08:28 PM
 
Where can I buy an 800Mhz eMac?!? I am dying to try this out and it is only for ~$600!
One iMac, iBook, one iPod, way too many PCs.
     
DeKU
Fresh-Faced Recruit
Join Date: Oct 2001
Location: Las Vegas, NV
Status: Offline
Reply With Quote
Jan 16, 2004, 09:09 PM
 
I overclocked a 1Ghz eMac to 1.33Ghz. no trouble yet. will go higher in the future. my soldering iron broke, so i took off the jumpers with an exacto knive and made a bridge with pencil markings. it works fine.
     
lbodnar
Fresh-Faced Recruit
Join Date: Jan 2004
Location: UK
Status: Offline
Reply With Quote
Jan 16, 2004, 09:17 PM
 
Guys, if you have never soldered before it is probably better to try it on something else first. Or better get someone to help you! They don't need to be computer experts. Average soldering skills and steady hands are ok.

The website has updated photos.
     
maninmac
Fresh-Faced Recruit
Join Date: Mar 2003
Location: Boston, MA
Status: Offline
Reply With Quote
Jan 16, 2004, 09:28 PM
 
Guys, I think I get it, but I do have a question:

In the image (attached) the gold colored pads are, I assume, the jumpers?

So to get to 1.3 ghz, I just solder the two pairs mentioned...

So my question is, do I need to remove the gold pad 'jumpers' or just put solder on top of them and join them?

Thanks!!!

R.
     
gotterdamm
Dedicated MacNNer
Join Date: Jan 2000
Status: Offline
Reply With Quote
Jan 16, 2004, 10:02 PM
 
Yes, I have a friend with soldering experience, but I think I'll need clearer instructions exactly what we're going to be soldering.

Sorry, but this is my first over-clocking.
     
jefferymac
Fresh-Faced Recruit
Join Date: Jan 2004
Status: Offline
Reply With Quote
Jan 17, 2004, 12:34 AM
 
I have a 700Mhz eMac, can I overclock this one as well?
     
Lateralus
Moderator Emeritus
Join Date: Sep 2001
Location: Arizona
Status: Offline
Reply With Quote
Jan 17, 2004, 01:22 AM
 
This is truly amazing, especially for those of you who paid $5xx for an eMac refurb. I mean... 1.33GHz+ of G4 power for less than $600!

Whats amazing is that a 1.467GHz processor upgrade for the Power Macs costs that much. Hell, even a good 1.25 upgrade costs a little over $400.

Incredible.

Bastards. Making me want to sell my Power Mac and buy an eMac...

...
I like chicken
I like liver
Meow Mix, Meow Mix
Please de-liv-er
     
Bluebomber21XX
Mac Enthusiast
Join Date: Feb 2001
Location: Livermore, California
Status: Offline
Reply With Quote
Jan 17, 2004, 01:34 AM
 
Okay, this is a crucial piece of information for anyone deciding to do this, especially those with no experience.

Working around exposed CRT's dangerous. If you don't know how to properly work around exposed CRT's, make sure you learn before you try this. You can get electrocuted. CRT's still carry a charge even when they are unplugged.

http://homepage.mac.com/jonzgoda/displaydischarge.pdf

Try the above link if you are worried about shocking yourself accidentally.
The online resource for Rockman & Forte!
http://www.bluebomber.com/
     
Lateralus
Moderator Emeritus
Join Date: Sep 2001
Location: Arizona
Status: Offline
Reply With Quote
Jan 17, 2004, 02:02 AM
 
Ah. Excellent point.

I remember when I was about 8 years old, I had taken apart an old black and white TV. I was sitting on the floor screwing around with the tube. I then touched the cap at the back of the tube... Then I remember being thrown to the floor...

An interesting experience to say the least. I couldn't stop shaking for almost 10 minutes.

I sometimes imagine the only reason that I survived was the fact that before my 'Curious George' self got a hold of the TV, it had been sitting in a storage shed for well over 10 years because it was dead. I imagine much of the electricity had disipated.

Ah, the joys of childhood...
( Last edited by Lateralus; Jan 17, 2004 at 05:39 PM. )
I like chicken
I like liver
Meow Mix, Meow Mix
Please de-liv-er
     
gthyb
Mac Enthusiast
Join Date: Mar 2001
Location: Columbia, MO
Status: Offline
Reply With Quote
Jan 17, 2004, 02:42 AM
 
I have an original G4 flat panel imac 800mhz. can I do the same thing to it? I'd like a HD bigger than 80 as well.

and it sure would be nice if apple's superdrive could burn 4x dvds faster than 1x.
     
yoyoman
Grizzled Veteran
Join Date: Dec 2002
Location: Cali
Status: Offline
Reply With Quote
Jan 17, 2004, 04:41 AM
 
Originally posted by gthyb:
I have an original G4 flat panel imac 800mhz. can I do the same thing to it? I'd like a HD bigger than 80 as well.

and it sure would be nice if apple's superdrive could burn 4x dvds faster than 1x.
Im getting a ibook and i believe its at 800 mhz would I be able to over clock that as well. Is the mother board similar to the emac sort of. Does any one have a link if not other wise?
     
Grrr
Grizzled Veteran
Join Date: Jun 2001
Location: London'ish
Status: Offline
Reply With Quote
Jan 17, 2004, 10:08 AM
 
I agree with ibodnar.. For those that have no soldering experience, I would not attempt this mod yet. Regular soldering can be tricky enough at times. But modern electronic stuff like the eMac uses surface mount technology which is another ball game entirely. And is rather more tricky to solder yourself. In fact ideally, it really needs specialist surface mount soldering equipment too. But at a push, just the SMD jumpers can be done with regular soldering equipment.
Oh, and dont forget your anti static precautions too!
Still not done this to my eMac yet.. but perhaps this weekend..
The worst thing about having a failing memory is..... no, it's gone.
     
lbodnar
Fresh-Faced Recruit
Join Date: Jan 2004
Location: UK
Status: Offline
Reply With Quote
Jan 17, 2004, 11:07 AM
 
Originally posted by Grrr:
.. But at a push, just the SMD jumpers can be done with regular soldering equipment.
Grrr, I just read the message somewhere this morning that some guy was so impatient that he removed existing jumpers with a pen knife and used graphite pencil to create shorts. That is the man!

I can't find the reference! Those messages are now everyhwere
     
Grrr
Grizzled Veteran
Join Date: Jun 2001
Location: London'ish
Status: Offline
Reply With Quote
Jan 17, 2004, 11:33 AM
 
Originally posted by DeKU:
I overclocked a 1Ghz eMac to 1.33Ghz. no trouble yet. will go higher in the future. my soldering iron broke, so i took off the jumpers with an exacto knive and made a bridge with pencil markings. it works fine.
This post you mean ibodnar?

Don't try this at home kids..
The worst thing about having a failing memory is..... no, it's gone.
     
lbodnar
Fresh-Faced Recruit
Join Date: Jan 2004
Location: UK
Status: Offline
Reply With Quote
Jan 17, 2004, 11:41 AM
 
Grrr, I am rolling on the floor!
I looked at about 10 message boards but not that one. Blind!

DeKU, how is your eMac doing?
     
Mac10
Fresh-Faced Recruit
Join Date: Jul 2003
Location: N.M.
Status: Offline
Reply With Quote
Jan 17, 2004, 09:49 PM
 
jefferymac asked:

"I have a 700Mhz eMac, can I overclock this one as well?"

Can someone let us know if it is possible to overclock the 700MHz eMac. I too have a 700MHz....would be nice to get it to 1GHz if possible, save me $1000 from buying a new one. If I recall the 700MHz eMac was using the 7450 chip and not the 7455, is this correct?

Thanks,
Ed
I have 13 Macs: 15Gig iPod, eMac/700, iBook/800, iMac/350, iBook/300, 7100/66, 6100/60, Performa 476, LC, SE/30, 3-Pluses, & a 512K w/030 accelerator board.
     
DeKU
Fresh-Faced Recruit
Join Date: Oct 2001
Location: Las Vegas, NV
Status: Offline
Reply With Quote
Jan 17, 2004, 09:54 PM
 
eMac is fine, it's actually my little brothers x-mas gift from yours truly. i removed 3 jumpers (R1506, R1512, R1518) by slowly scraping the solder off one side and the twisting the blade once in to fully remove it. they just pop off. i needed to bridge R1515 so i used a 0.3 lead pencil to bridge it.

Little brother has been playing plenty of halo and aliens vs. predator on hours end and the machine has not crashed. i'll try to bump it to 1.4 GHz as soon as i can.

for those who dont want to do a pencil bridge, another goofy way to do the bridge is by taping a tiny square of aluminum foil on the conductors. works fine as well. (dont know what prolonged effects if any, heat will have on the tape.)
     
lbodnar
Fresh-Faced Recruit
Join Date: Jan 2004
Location: UK
Status: Offline
Reply With Quote
Jan 17, 2004, 10:12 PM
 
If you go that road the best bet is electrically conductive silver paint. It is about $5..10 a pot in hobby/electronics shops. They sell it for PCB repairs. Or shorting the pads
     
Lateralus
Moderator Emeritus
Join Date: Sep 2001
Location: Arizona
Status: Offline
Reply With Quote
Jan 17, 2004, 11:29 PM
 
Originally posted by Mac10:
jefferymac asked:

"I have a 700Mhz eMac, can I overclock this one as well?"

Can someone let us know if it is possible to overclock the 700MHz eMac. I too have a 700MHz....would be nice to get it to 1GHz if possible, save me $1000 from buying a new one. If I recall the 700MHz eMac was using the 7450 chip and not the 7455, is this correct?

Thanks,
Ed
No, unfortunately your eMac would not be overclockable, atleast not significantly enough to justify the risk of damage to the hardware that comes with soldering. The 7450 topped out at around 800MHz.
I like chicken
I like liver
Meow Mix, Meow Mix
Please de-liv-er
     
RAMdrd
Fresh-Faced Recruit
Join Date: Aug 2000
Status: Offline
Reply With Quote
Jan 18, 2004, 01:28 AM
 
Those of you who have actually spent some time around the Mac may remember an article by MacAddict where they modified jumpers to overclock a Mac.

For those interested, a little research can find it, I'm sure.

Same thing for the dual monitor/spanning hack. This has been available for some of the newer iBooks for awhile.

I'd just like to know how people like lbodnar find this stuff out!

If one doesn't want to take the chance, that's understandable. But try to have a *little* objectivity.

And if you *do* try this, I'd recommend avoiding "pencil bridges" or tin foil pathways. If you can't do any soldering, maybe you should pass.

But very cool of lbodnar to share all this information, detail, and great pictures.

This is too too cool!
     
Dex13
Mac Elite
Join Date: Dec 2002
Location: Bay Area of San Jose
Status: Offline
Reply With Quote
Jan 18, 2004, 01:44 AM
 
Originally posted by klinux:
Where can I buy an 800Mhz eMac?!? I am dying to try this out and it is only for ~$600!
Yeah does anyone know exactly where one can buy one besides ebay?
     
gthyb
Mac Enthusiast
Join Date: Mar 2001
Location: Columbia, MO
Status: Offline
Reply With Quote
Jan 18, 2004, 02:00 AM
 
the apple store has some cheap ones in the deals section. they also have some that are even less refurbished.
     
Sheep
Junior Member
Join Date: Jun 2002
Location: Belgium
Status: Offline
Reply With Quote
Jan 18, 2004, 08:37 AM
 
Originally posted by gthyb:
I have an original G4 flat panel imac 800mhz. can I do the same thing to it? I'd like a HD bigger than 80 as well.

and it sure would be nice if apple's superdrive could burn 4x dvds faster than 1x.
I have the same original iMac 800Mhz with 2x SuperDrive. Your problem that disks are being burned at 1x is teh media. I had a couple of Memorex dvd's and they all burned at 1x, then I got the Apple dvd's and they burned at 2x. So it's probably teh media.
But the original iMac with SuperDrive will not burn faster then 2x though
     
nickday
Junior Member
Join Date: Mar 2003
Location: Chester, UK
Status: Offline
Reply With Quote
Jan 18, 2004, 12:12 PM
 
Wow! I'm thinking of getting a 1ghz eMac, would I be able to overclock that to 1.33ghz, or would I have to get a 800mhz?

Cheeers,
Nick
     
lbodnar
Fresh-Faced Recruit
Join Date: Jan 2004
Location: UK
Status: Offline
Reply With Quote
Jan 18, 2004, 12:17 PM
 
Originally posted by nickday:
Wow! I'm thinking of getting a 1ghz eMac, would I be able to overclock that to 1.33ghz, or would I have to get a 800mhz?
800 and 1GHz are exactly the same apart from a CPU. I don't know where the 1GHz's limit is but people run it at 1.4GHz:

http://bbs.xlr8yourmac.com/ubb/Forum11/HTML/001019.html
     
lbodnar
Fresh-Faced Recruit
Join Date: Jan 2004
Location: UK
Status: Offline
Reply With Quote
Jan 18, 2004, 07:44 PM
 
OK, just an update.

I can reliably run my 800Mhz eMac at 1.4GHz but with a little bit of extra work.

I have replaced the thermo-conductive pad between the processor and a heatsink for a grease. Also I have opened the bottom hatch and placed an extra fan to blow the air inside. I am not impressed with an airflow inside eMac - probably making something like a funnel or airflow quides to route the air properly will do the job. By Apple design this tiny heatsink just sits in a rather big cave and air is being sucked out of it. There should be a dedicated airflow through it!

I have also tried 1.46GHz - there is a startup chime but no video. That's it. The limit.

But 800MHz -> 1.4GHz has been achieved!

That is 75% increase - is is sorta new World Record?
     
Grrr
Grizzled Veteran
Join Date: Jun 2001
Location: London'ish
Status: Offline
Reply With Quote
Jan 18, 2004, 09:30 PM
 
Crikey!

Well done!

*Off to buy thermo conductive paste*
The worst thing about having a failing memory is..... no, it's gone.
     
gthyb
Mac Enthusiast
Join Date: Mar 2001
Location: Columbia, MO
Status: Offline
Reply With Quote
Jan 19, 2004, 01:44 AM
 
oh, yeah i know its the media. its just that 2x media is getting harder and harder to find, and i believe the problem was fixed through a firmware update for windows users, i just wish apple/pioneer would do the same.
     
revargent
Fresh-Faced Recruit
Join Date: Jun 2003
Status: Offline
Reply With Quote
Jan 19, 2004, 01:48 AM
 
Originally posted by Anand:
http://www.lbodnar.dsl.pipex.com/eMac/eMac-upgrade.html

Anyone else willing to give it a try?
I'm more interested in the second part of the article. 800 MHz seems plenty fast enough (I'm currently on G3/266), but what's holding me back from the eMac is that godawful shadow-mask screen. I'm almost at the point of trying to mount an eMac motherboard in a PC minitower so I don't even have to have that cheesy monitor in the same room as me.
     
Grrr
Grizzled Veteran
Join Date: Jun 2001
Location: London'ish
Status: Offline
Reply With Quote
Jan 20, 2004, 01:38 AM
 
I rather like the screen actually.. Only the cheapo front panel makes it look crap, in my opinion.

Anyway, another 1.33GHz eMac is born!
Working very nicely so far. eMacs are a sh!t to take apart though! I had to do it twice too, as I stupidly forgot to reconnect the HD power cable 1st time around. And those micro jumpers are even smaller than I was expecting! Still, got the job done eventually.
The worst thing about having a failing memory is..... no, it's gone.
     
CobaltGT
Junior Member
Join Date: Dec 2001
Location: Georgia Tech
Status: Offline
Reply With Quote
Jan 20, 2004, 01:25 PM
 
Leo, what's the pll config for 1.466?
     
lbodnar
Fresh-Faced Recruit
Join Date: Jan 2004
Location: UK
Status: Offline
Reply With Quote
Jan 20, 2004, 01:51 PM
 
1.4GHz:
-
close
close
close
-

1.466GHz
-
close
close
-
-

1.532GHz
close
close
close
close
close

1.6GHz
-
close
-
-
-

Good luck! Guys, when you are at some stable level (with either success or not) please submit to xlr8yourmac CPU db - it's nice to have one place for statistics.
     
 
Thread Tools
 
Forum Links
Forum Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Top
Privacy Policy
All times are GMT -4. The time now is 06:37 PM.
All contents of these forums © 1995-2017 MacNN. All rights reserved.
Branding + Design: www.gesamtbild.com
vBulletin v.3.8.8 © 2000-2017, Jelsoft Enterprises Ltd.,